Contact Us
✖

    Force sensors & Load Cells

    Filter by Image Clear All
    MLA26 Single Point Load Cell
    MLT62 Tension and Compression Force Sensor
    MLC25 High Capacity Column Type Compression Load Cell
    MLW67 Button Type Compression Load Cell
    1 2 3 4 5 6 7

    Load cells for weighing and force measurement

    A load cell sensor reports force, but the reading only means something if the cell suits the way the load arrives. A load that acts off-centre, a side load, a mounting surface that is not flat, or a rated capacity set too close to the peak force can each move a reading or damage the cell. Our load cells allow the test engineer or weighing system designer to match the cell to the load, the mounting and the environment, which helps the reading stay on the force being measured, from miniature force sensors to column cells for tonnes of load.

    Every instrument is selected on several testing and environmental parameters: the capacity and direction of the load, the mounting, and the accuracy class and protection rating. To help you achieve these objectives, our in-house applications engineers can help you define the project scope and application, select the equipment, and assist with system integration and technical support.

    Load cells

    We offer a wide range of load cells commonly found in weighing systems, test rigs, hoppers and structural monitoring in Australia, which can be used to measure compression, tension and shear force. MeasureX supplies them and can modify them for your application, and the standard capacities run from 0.1 kg to 500 t.

    Single point load cell

    A single point load cell is designed for loads that act off-centre on a platform, which suits platform scales and check weighers. The range includes a low range version and a hermetically sealed version.

    Shear beam load cell

    A shear beam load cell is mounted beneath hoppers, tanks and silos, where the weighing system load cell carries the vessel weight through the beam.

    Column type load cell

    A column type load cell measures compression, and the range runs from standard column cells to a high capacity version and a miniature column type.

    Double ended shear beam load cell

    The double ended shear beam load cells are supported at both ends and loaded in the middle, and one version is a pin type for pinned connections.

    S-type load cell and tension compression load cell

    An S-type load cell measures tension and compression, so one tension compression load cell covers a pull and a push, as in hanging scales and test rigs. A miniature S-type force sensor is also available.

    Shear web load cell

    The shear web load cells include compression and centre thread versions, and a tension and compression version, for test rigs and machine builds.

    Miniature load cell

    A miniature load cell suits limited space. The range includes a miniature compression cell, an ultra-miniature centre thread cell, and miniature tension and compression force sensors, and each mini load cell is a force sensor for low range work.

    3-axis load cell

    A 3-axis load cell reports force along three directions at once, so one multi-axis load cell separates the components of a force. The range has a standard and a compact version.

    Centre hole load cells

    The centre hole load cells are ring shaped, so a rod, bolt or cable can pass through the cell, and the range includes a low profile version.

    OEM load cells and custom load cells

    A load cell specified into a product carries into production, so the selection is worth settling early. When a standard cell does not fit, custom load cells range from a modification of a standard product to a complete custom design.

    Comparing load cell types by how the force arrives

    The load cells in this range are strain gauge types, and each reports force as a signal that is proportional to the load. What differs is how the force reaches the cell.

    Compression cells, such as the column, shear web and centre hole types, take a push. Tension and compression cells, such as the S-type, take a push or a pull. Beam cells carry a vessel or platform through a beam, and single point cells take a load that acts off-centre on a platform.

    The 3-axis cells separate force into its components, and the miniature cells keep the same ideas in a small body for low range work.

    Choosing load cells for your measurement

    Start with the load. Choose a rated capacity that comfortably exceeds the maximum expected force, and allow for overload protection, because a cell should not be used above its rated capacity. Then settle the accuracy class, the protection rating, which runs from IP62 to IP68 in this range, and the output your indicator, logger or amplifier accepts. The load cell selection guide covers mounting, side loads and cable protection as well. Accuracy options run from 0.01% to 1% of full scale.

    Are you measuring for a test programme, building a weighing system for a client, or designing the cell into a product? A test engineer wants a cell that matches the rig and the data acquisition system, a consultant writes a specification that others buy against, and an OEM designer needs the cell and its excitation to fit the product. The engineers can work from your answer to a shortlist.

    Selection and technical support

    Our applications engineers define the project scope and application with you, help select the load cell, and assist with system integration. They can visit site for demonstration and testing, assist with your own installation and commissioning, and provide technical support after the sale.

    Frequently asked questions

    Yes. The S-type cells, and the tension and compression versions in the shear web and miniature ranges, take both. A compression cell takes a push only.

    Most load cells give a millivolt per volt output, which needs a bridge input or an amplifier, and some versions give 4-20mA or voltage output. A signal conditioner converts a millivolt output to a standard signal, and the engineers can check a candidate cell against your equipment before you order.

    Shear beam and double ended shear beam cells are the usual starting point, with the column type for compression loads. The mounting and any side loads decide the final choice, and the engineers can review them with you.

    Talk to us about your load measurement

    To discuss a measurement, have a chat with us about your application.

    © 2015-2026 Measurex. All Rights Reserved.

    Select at least 2 products
    to compare